Difference between revisions of "1-Wire Hub"
From PhotoVoltaic Logger new generation
m (→Draft) |
m (→Draft) |
||
| Line 11: | Line 11: | ||
If you have long 1-Wire network runs and are having problems with glitches you should add a Schottky diode to the end of your network. Typically a 1N5817 diode reverse biased across sensors will achieve this. Solder the side with the stripe to data output (DQ pin 2) and the other side to ground (GND pin 1) of the DS18S20. | If you have long 1-Wire network runs and are having problems with glitches you should add a Schottky diode to the end of your network. Typically a 1N5817 diode reverse biased across sensors will achieve this. Solder the side with the stripe to data output (DQ pin 2) and the other side to ground (GND pin 1) of the DS18S20. | ||
| − | == Draft | + | == Normal mode == |
| + | |||
| + | Typical wiring looks like this. | ||
| + | |||
| + | |||
| + | [[File:1-WireNormal.png]] | ||
| + | |||
| + | |||
| + | But Dallas recommends a long wire, so I adapted the wirng to this scheme. | ||
| + | |||
| + | |||
| + | [[File:1-WireLong.png]] | ||
| + | |||
| + | |||
| + | = Draft = | ||
[[File:DS1820.png|right]] | [[File:DS1820.png|right]] | ||
Revision as of 16:07, 12 November 2017
Contents
I monitor here 3 1-Wire DS18B20[1] based temperature sensors.
As I looked at commercial solutions and their prices, I decided to construct my own 1-Wire hub.
The DS18B20 temperature sensor can be powered by an external supply on the VDD pin, or it can operate in "parasite power" mode, which allows the DS18B20 to function without a local external supply[2].
- In normal mode, each sensor is connected between a power line (VDD pin 3) and ground (GND pin 1), and the data output (DQ pin 2) connects to a third, data, line. The data output is a 3-state or open-drain port (DQ pin 2) and a 4.7 kΩ pull-up resistor to the power line is required.
- Parasite power mode requires both DS18B20 GND (pin 1) and VDD (pin 3) to be connected to ground. The DQ pin (pin 2 - the middle pin) is the data/parasite power line. The data line requires also a pull-up resistor of 4.7 kΩ connected to +5 V.
If you have long 1-Wire network runs and are having problems with glitches you should add a Schottky diode to the end of your network. Typically a 1N5817 diode reverse biased across sensors will achieve this. Solder the side with the stripe to data output (DQ pin 2) and the other side to ground (GND pin 1) of the DS18S20.
Normal mode
Typical wiring looks like this.
But Dallas recommends a long wire, so I adapted the wirng to this scheme.
Draft
So put all together to get an imagination.
(You can also bridge all not used D+ & D- connection points.)
The trick to build a linear topology is, that each sensor is connected with 4 wires. The DQ data pin 2 is connected with 2 wires of the cable, to build a single long line.
Please note: Mind the diode and the resistor!
Build
- As small as possible
- Simple to build > breadboard platine
- Stable > Normal mode
- Linear topology (according to this guidelines) > more stable than star topologies
Put it all together and minimize.
Next Version 2 will fit into a case for a cap rails.
(View from top, printed circuits and soldering on the bottom)
The cyan, red and black thick dots are the soldering points for the upstream Data, +5V and GND wires.
Use a bit thicker telephone cable J-Y(St)Y 2x2x0.8mm for lower loop impedance.
| Parts list | Source of supply | Price |
|---|---|---|
| Lötbare Schraubklemme, RM 5.0mm | Conrad | € 0.33 |
| Lötstreifenrasterplatte | Conrad | € 2.94 |
| Schottky-Diode 1N5817RLG alternative: Diode 1N4001 50V/1A |
Conrad Conrad |
€ 0.25 € 0.06 |
| Kohleschicht-Widerstand 4,7 kΩ | Conrad | € 0.10 |
| Universal-Gehäuse 120x65x40 BOXE | Conrad | € 3.98 |
| Telefoninnenkabel J-Y(ST)Y 2x2x0.8mm | Conrad, eBay | € 1.19/m |
